• ICND2 Labs

    Lab 5-2: Establishing a Frame Relay Connection

    Physical Topology Diagram Visual Topology Command Line Task 1: Setting up a basic Frame-relay link Task 2: Supporting Frame-relay using sub-interfaces Visual Topology Command Line Command Description encapsulation Frame-relay Enables Frame-relay encapsulation on an interface Frame-relay interface-dlci dlci Assigns a DLCI to an interface or subinterface Interface interface.subinterface point-topoint Creates a frame-relay point-to-point subinterface Show frame-relay lmi Display LMI statistics…

  • ICND2 Labs

    Lab 5-1: Setting up a Serial Connection

    Physical Topology Diagram Visual Topology Command Line Task 1: Using HDLC Task 2: Configuring PPP Task 3: Setting up PPP authentication Visual Topology Command Line Command Description debug ppp authentication Displays the PPP authentication process in real time debug ppp negotiation Displays the PPP negotiation packet exchange encapsulation HDLC Enables HDLC encapsulation on an interface encapsulation PPP Enables PPP encapsulation…

  • ICND2 Labs

    Lab 4-2: Implementing OSPF for IPv6

    Physical Topology Diagram Visual Topology Command Line Task 1: Enabling OSPFv3 Visual Topology Command Line Command Description ipv6 ospf process id area id Enables OSPFv3 on an interface ipv6 router ospf process id Enters the OSPFv3 configuration mode router-id id Set a 32 bit router-id (dotted decimal notation) Show ipv6 ospf interface brief Displays interfaces that are enabled for OSPFv3…

  • ICND2 Labs

    Lab 4-1: Implementing OSPF in a Multi-area Environment

    Physical Topology Diagram Visual Topology Command Line Task 1: Configuring a multi-area OSPF network. Visual Topology Command List Command Description network address wildcard mask area id Specifies which interfaces are OSPF capable and links them to an OSPF area router ospf process id Enters the OSPF router configuration mode show ip ospf interfaces brief Displays OSPF interface information show ip ospf…

  • ICND2 Labs

    Lab 3-2: Implementing EIGRP for IPv6

    Physical Topology Diagram Visual Topology Command Line Task 1: Setting up IPv6 on the interface. Task 2: Enabling EIGRP for IPv6. Visual Topology Command List Command Description ipv6 address address / mask Applies an IPv6 address to an interface ipv6 eigrp AS number Configures EIGRP for IPv6 on an interface ipv6 router eigrp AS number Enters the IPv6 EIGRP configuration mode…

  • ICND2 Labs

    Lab 3-1: Implementing EIGRP

    Physical Topology Diagram Visual Topology Command List Task 1: Remote network connectivity. Task 2: Configure EIGRP Task 3: Using show commands to verify EIGRP parameters Visual Topology Command List Command Description debug eigrp neighbors Debugs eigrp events network network [wildcard mask] Enables the routing protocol on the interfaces, an optional wildcard mask can be used to narrow down the interface list…

  • ICND2 Labs

    Lab 1-3: Configuring EtherChannel

    Physical Topology Diagram Visual Topology Command List Task 1: EtherChannel configuration Visual Topology Command List Command Description Channel-group id mode active Configures an interface as EtherChannel bundle members using LACP in active mode. Channel-group id mode passive Configures an interface as EtherChannel bundle members using LACP in passive mode. Configure Terminal Enters global configuration mode. Copy run start Saves the dynamic…

  • ICND2 Labs

    Lab 1-2: Optimizing STP

    Physical Topology Diagram Visual Topology Command List Task 1: Verify STP operation. Task 2: Manipulating Root Bridge selection. Task 3: Configuring Rapid Spanning-tree Task 4: Using STP Portfast. Visual Topology Command List Command Description Configure Terminal Enters global configuration mode. Copy run start Saves the dynamic running-config to NVRAM. [no] debug spanning-tree events Interface Fastethernet 0/0 Specifies interface fa0/0 Interface Gigabitethernet…

  • ICND2 Labs

    Lab 1-1: VLANs and Trunks Connections

    Physical Topology Diagram Visual Topology Command List Task 1: Reload and check that the Switch is set to factory defaults. Task 2: Basic switch set-up. Task 3: Configure basic VLAN and Trunk connections. Task 4: Troubleshoot Trunk failure. Visual Topology Command List Command Description Configure Terminal Enters global configuration mode Copy run start Saves your dynamic running config to NVRAM Delete…

  • ICND1 Labs

    Lab 5-2: Configure IPv6 Routing

    Visual Topology Command Line Command Description ipv6 ospf process id area id Enables OSPFv3 on the interface ipv6 router ospf process id Enters OSPFv3 router configuration mode Ping address Checks end to end connectivity router-id 32bit id Assigns a 32 bit router-id in a dotted decimal format, example (1.1.1.1) show ipv6 ospf Displays OSPFv3 settings show ipv6 ospf neighbor Displays…

Back to top button