OSPF Practice Skills Assessment – Packet Tracer CCNA Routing and Switching – Scaling Networks [alert-announce]Connect the PC to the Switch/Router using a Console cable[/alert-announce] Router: Administration / HQ / Town-HalL en conf terminal ip route 0.0.0.0 0.0.0.0 s0/1/0 ipv6 unicast-routing ipv6 route ::/0 s0/1/0 router ospf 10 network 10.10.10.0 0.0.0.3 …
Read More »CCNA 3 ScaN v6.0 – EIGRP Practice Skills Assessment – PT 100% Scores
[alert-note]If you only getting 75%, please temporarily uninstall Packet Tracer current version. Please download and setup “Cisco Packet Tracer 7.0” and Retake Assessment to getting 100% scores. Goodluck! 🙂 [/alert-note] Download Full: pka file, PDF file and Answers – 100% Score
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Final Exam Answers 2019
Which routing protocol is able to scale for large networks and utilizes non-backbone areas for expansion? EIGRP BGP OSPF* RIPv2 In the Cisco hierarchical design model, which layer is more likely to have a fixed configuration switch than the other layers? distribution transport internet access* core A network engineer is …
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Practice Final Exam Answers 2019
The network administrator wants to configure a switch to pass VLAN update information to other switches in the domain but not update its own local VLAN database. Which two steps should the administrator perform to achieve this? (Choose two.) Reset the VTP counters. Configure the switch with the same VTP …
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Chapter 10 Exam Answers 2019
Which two parameters must match between neighboring OSPF routers in order to form an adjacency? (Choose two.) router ID IP address process ID cost hello / dead timers* network types* Which command can be used to view the OSPF hello and dead time intervals? show ip protocols show ip ospf …
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Chapter 9 Exam Answers 2019
What are two reasons for creating an OSPF networkWhat information is contained within an OSPF type 4 LSA with multiple areas? (Choose two.) to simplify configuration to reduce SPF calculations* to reduce use of memory and processor resources* to provide areas in the network for routers that are not running …
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Chapter 8 Exam Answers 2019
By default, what is the OSPF cost for any link with a bandwidth of 100 Mb/s or greater? 100 100000000 1* 10000 Which command will verify that a router that is running OSPFv3 has formed an adjacency with other routers in its OSPF area? show ipv6 interface brief show ipv6 …
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Chapter 7 Exam Answers 2019
In which scenario will the use of EIGRP automatic summarization cause inconsistent routing in a network? when the routers in an IPv4 network have mismatching EIGRP AS numbers when the routers in an IPv4 network are connected to discontiguous networks with automatic summarization enabled* when there is no adjacency that …
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Chapter 6 Exam Answers 2019
Refer to the exhibit. Which two networks contain feasible successors? (Choose two.) 10.44.100.252* 10.44.101.252 192.168.71.0* 192.168.51.0 10.44.104.253 Which three metric weights are set to zero by default when costs in EIGRP are being calculated? (Choose three.) k5* k6 k2* k4* k3 k1 What information does EIGRP maintain within the routing …
Read More »CCNA 3 Scaling Networks v6.0 – ScaN Chapter 5 Exam Answers 2019
Which routing protocol is designed to use areas to scale large hierarchical networks? RIP OSPF* EIGRP BGP Which routing protocol uses link-state information to build a map of the topology for computing the best path to each destination network? RIP RIPng OSPF* EIGRP After a network topology change occurs, which …
Read More »