120 Labs for Cisco CCNA 200-125 and CCENT Exams

Lab 5: Configuring Standard VLANs on Catalyst Switches

Lab Objective:

The objective of this lab exercise is for you to learn and understand how to configure standard VLANs 1–1001 on Cisco Catalyst IOS Switches. In addition, you are also required to familiarize yourself with the commands available in Cisco IOS to validate and check your configurations.

Lab Purpose:

VLAN configuration is a fundamental skill. VLANs allow you to segment your network into multiple, smaller broadcast domains. As a Cisco engineer, as well as in the Cisco CCNA exam, you will be expected to know how to configure VLANs on Cisco switches.

Certification Level:

This lab is suitable for both CCENT and CCNA certification exam preparation.

Lab Difficulty:

This lab has a difficulty rating of 4/10.

Readiness Assessment:

When you are ready for your certification exam, you should complete this lab in no more than 10 minutes.

 Lab Topology:

Please use the following topology to complete this lab exercise:

Task 1:

In preparation for VLAN configuration, configure a hostname on Sw1 as well as the VLANs depicted in the topology.

Task 2:

Configure ports FastEthernet0/5 to FastEthernet0/8 as access ports and assign them to the VLANs specified.

Task 3:

Verify your VLAN configuration using relevant show commands in Cisco IOS.

Configuration and Verification

Task 1:

Switch#config t 
Enter configuration commands, one per line.  End with CTRL/Z. 
Switch(config)#hostname Sw1 
Sw1(config-vlan)#name SALES 
Sw1(config-vlan)#name MANAGERS 
Sw1(config-vlan)#name ENGINEERS 
Sw1(config-vlan)#name SUPPORT

NOTE: By default, Cisco switches are VTP servers so no configuration is necessary for server mode. Use the show vtp status command to look at the current VTP operating mode of the switch.

Task 2:

Sw1(config)#interface fastethernet0/5 
Sw1(config-if)#switchport mode access 
Sw1(config-if)#switchport access vlan10 
Sw1(config)#interface fastethernet0/6 
Sw1(config-if)#switchport mode access 
Sw1(config-if)#switchport access vlan20 
Sw1(config)#interface fastethernet0/7 
Sw1(config-if)#switchport mode access 
Sw1(config-if)#switchport access vlan30 
Sw1(config)#interface fastethernet0/8 
Sw1(config-if)#switchport mode access 
Sw1(config-if)#switchport access vlan40

Task 3:

Sw1#show vlan brief
VLAN Name                    Status    Ports
—- ———————– ——— ——————————-
1    default                 active    Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/9, Fa0/10, Fa0/11, Fa0/12
Fa0/13, Fa0/14, Fa0/15, Fa0/16
Fa0/17, Fa0/18, Fa0/19, Fa0/20
Fa0/21, Fa0/22, Fa0/23, Fa0/24
Gi0/1, Gi0/2
10   SALES                   active    Fa0/5
20   MANAGERS                active    Fa0/6
30   ENGINEERS               active    Fa0/7
40   SUPPORT                 active    Fa0/8
1002 fddi-default            active
1003 token-ring-default      active
1004 fddinet-default         active
1005 trnet-default           active

Related Articles

Notify of

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Inline Feedbacks
View all comments
Back to top button