The objective of this lab exercise is for you to learn and understand how to manually configure OSPFv3, which is a core ICND2 and CCNA topic.
Manually configure IPv6 interface addressing and then configure a Single-Area OSPFv3 connection.
This lab is suitable for ICND2 and CCNA certification exam preparation.
This lab has a difficulty rating of 7/10.
When you are ready for your certification exam, you should complete this lab in no more than 10 minutes.
Please use the following topology to complete this lab exercise:
Configure hostnames on routers R1 and R3 as illustrated in the topology.
Configure the IPv6 addresses on the FastEthernet interfaces of R1 and R3 as illustrated in the topology.
Enable OSPF in area 0 between R1 and R3. For R1, use OSPF process ID 1. For R3, use OSPF process ID 3. Configure router ID 18.104.22.168 for R1 and 22.214.171.124 for R3.
Ping across the link and then use the relevant show commands to verify your configurations.
Configuration and Verification
For reference information on configuring hostnames, please refer to earlier labs.
R1#conf t R1(config)#ipv6 unicast-routing Enter configuration commands, one per line. End with CTRL/Z. R1(config)#int f0/0 R1(config-if)#ipv6 address 3fff:1234:abcd:1::1/64 R3#conf t R3(config)#ipv6 unicast-routing R3(config-if)#int f0/0 R3(config-if)#ipv6 address 3fff:1234:abcd:1::3/64
R1(config)#ipv6 router ospf 1 R1(config-rtr)# *Mar 1 00:05:32.755: %OSPFv3-4-NORTRID: OSPFv3 process 1 could not pick a router-id, please configure manually R1(config-rtr)#router-id 126.96.36.199 R1(config-rtr)#int f0/0 R1(config-if)#ipv6 ospf 1 area 0 R1(config-if)#end R3(config)#ipv6 router ospf 3 R3(config-rtr)# *Mar 1 00:06:57.451: %OSPFv3-4-NORTRID: OSPFv3 process 3 could not pick a router-id, please configure manually R3(config-rtr)#router-id 188.8.131.52 R3(config-rtr)#int f0/0 R3(config-if)#ipv6 ospf 3 area 0 R3(config-if)#exit
R1#ping ipv6 3fff:1234:abcd:1::3 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 3FFF:1234:ABCD:1::3, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/22/36 ms *Mar 1 00:09:12.183: %OSPFv3-5-ADJCHG: Process 1, Nbr 184.108.40.206 on FastEthernet0/0 from LOADING to FULL, Loading Done R1#show ipv6 ospf nei Neighbor ID Pri State Dead Time Interface ID Interface 220.127.116.11 1 FULL/DR 00:00:39 4 FastEthernet0/0 R1#show ipv6 ospf nei detail Neighbor 18.104.22.168 In the area 0 via interface FastEthernet0/0 Neighbor: interface-id 4, link-local address FE80::C001:8FF:FE52:0 Neighbor priority is 1, State is FULL, 6 state changes DR is 22.214.171.124 BDR is 126.96.36.199 Options is 0x674EE6BD Dead timer due in 00:00:38 Neighbor is up for 00:01:01 Index 1/1,retransmission queue length 0,number of retransmission 0 First 0x0(0)/0x0(0)/0x0(0) Next 0x0(0)/0x0(0)/0x0(0) Last retransmission scan length is 0, maximum is 0 Last retransmission scan time is 0 msec, maximum is 0 msec R1#show ipv6 int brie FastEthernet0/0 [up/up] FE80::C000:8FF:FE52:0 3FFF:1234:ABCD:1::1